Skip to main content

Water Tube Coil Type Boilers (REVOSTEAM)

Image
By

REVOSTEAM - Coil Type Boiler is that the standard forced-circulation type water tube coil type boiler incorporating the distinctive principle of combustion called ‘Reverse Flow’. Revosteam will increase the combustion potency and permits a high rate of heat unharness. It may be offered in each IBR and Non-IBR Boilers designs.

Construction:


       Water tube Coil type boiler includes a jacketed MS shell housing a volume coil. The combustion air is forced through the jacketed shell by means that of a centrifugal blower thereby obtaining pre-heated. The flame travels downwardly within the coil and therefore the flue gases reverse upwards thereby giving 2 passes within the beaming zone guaranteeing complete combustion and better heat flux. The third pass of the flue gases is within the convective zone between the coil and therefore the inner shell. Flue gases then travel the saver forming the fourth pass.

Advantages:



  1. Fully Automatic unit
  2. Unique four pass design
  3. High potency and low running value
  4. Minimum site-work, low installation prices
  5. Instant steaming among five minutes of cold begin
  6. Built-in saver will increase the operational potency
  7. Fail-safe design and dependable operational instruments

Capacity :

   
  Revosteam- Water Tube Coil type Boiler is offered in capacities from 100Kg/hr to 200Kg/hr.
Water Tube Coil Type Boilers

Labels:

Comments

Post a Comment

Popular posts from this blog

Products of Thermodyne Boilers

By
Thermodyne Boilers Products: Thermodyne Engineering Systems - Manufacturer and Supplier of Hot Air Generators , Hot Water Generators , Thermic Fluid Heaters, Coil type boilers , Electrode type boilers , Oil / gas fired boilers , Solid fuel-fired boilers & Waste heat recovery boilers , IBR & Non-IBR Boilers, Steam Boilers , Hot Water Boilers, Energy saving devices, Thermal Energy Consultancy, Steam Piping, Pollution Control Equipment, Boiler Water Chemicals . Thermodyne Engineering systems A – 7/108 & A – 7/110, SSGT Road Industrial Area, Ghaziabad – 201009, Uttar Pradesh (India). Mobile No.  : +91- 9990226006  +91-120-4110482, Products of Thermodyne Engineering systems: Packaged Boilers - Intech Oil and Gas Fired Boilers - Savemax Combi Boilers- Combitherm Combi Boiler - Ultra Model Industrial Chimney Condensate Recovery Systems Electrode Boiler- Electra Thermic Fluid Heater - Fluidtherm ...
1 comment
Read more

What is Mobrey

By
What is Mobrey? Mobrey  is the name used for the  Automatic water level controller , it comes under the category of mountings and fittings of  Steam Boiler Assembly . As the name suggests, it is used for maintaining the water level in the Boiler shell. It is mostly used in  smoke tube steam boilers  not in  water tube boilers , as the shell diameter of the former is greater than that of latter irrespective of their running capacities and working pressures. We at  Thermodyne Boilers  had supplied and installed successfully these Mobrey (automatic water level controllers) to all our clients. For  smoke tube boilers , mobrey is fitted externally on the nozzles coming out of the s team boiler  shell curvature.  It consists of a hollow cylindrical unit in which a float hangs. So, when the feed pump works, it supplies feed water to the boiler shell and it gets filled up. From those nozzles, the water also enters the hollow cylin...
2 comments
Read more

Why spirals are provided at the Idustrial Boiler Chimney

By
Chimney:- Chimney , as we know, is used to reject the flue gases to the atmosphere, coming from the Steam Boiler during operation. Also, it is a megastructure in Steam Boiler assembly and any discrepancy in its structural and foundation work can cause extremely serious damages, may even lead to casualties or plant shut off till its re-erection. The designer must consider all the factors while designing chimneys and one of the major factors amongst them is the wind factor. Blowing wind tries to overcome its static inertia but fails, if spirals are provided on the surface of the chimney. BUT THE QUESTION IS HOW????? Consider a chimneys (without spiral wings) , when the blowing wind comes in contact with its upstream surface, stagnation point (zero velocity) is achieved at that point i.e. pressure generated is high at that point and at the downstream end a vacuum is created as the wind coming in contact with the chimneys , gets deflected and meets after some point (wake regio...
8 comments
Read more